Micro suction cup suited for light use to mount a bullet camera inside or out. Very strong for its size, although possibly not stable enough for a camcorder unless it's really small. This is a fantastic little suction mount suitable for bullet cameras. It will work with any of our bullet cameras and has an adjustable ball joint so you can angle the camera to get the shot you require. Works well with car and bike fairings.

Dimensions: 75mm (h) x 65mm (dia)

Small suction cup, that is lever operated, producing a huge amount of grip from such a small suction mount. Rated as holding a maximum of 500g by the manufacturer, we have tested this at a higher weight. Best suited to sticking bullet cameras onto parts where larger mounts are unable to fix. This suction mount is a bit bigger than the mount above and will give slightly better stability. Still only recommended for bullet cameras or very small cameras.

Dimensions: 85mm (h) x 68mm (dia)

This is a high quality suction mount made by Cullmann. This will sucker to any shiny surface. It has a pressure lever for getting extra suction. This mount is suitable for bullet cameras and small to medium camcorders.
95mm diameter suction cup, with ball and socket head. Manufacturer rated to 3kg, and we have tested this suction mount in excess of this (in ideal conditions).

Dimensions: 120mm (h) x 95mm (dia)

This is one of the most popular suction mounts we sell. It has super strong suction using a lever compression arm and has a pivot point and a fully adjustable ball head.
Single suction mount, which can be mounted inside and outside cars, sometimes even on a helmet. If using on a helmet they stick better on areas of helmets not covered in vinyl stickers. Best suited to using bullet cameras, small still cameras and small camcorders.

Dimensions: 90 - 150mm (h) x 80mm (dia)

A strong, all metal suction mount with three suckers. Has a small size, making it ideal for positioning a bullet on small panels (bumper, lights etc).

This mount works well with bullet cameras and small camcorders as well as DSC's. It will hold about 5kg in weight or a bullet camera at over 200mph! Ideal for both bikes and cars, using 3 smaller suckers gives good stability on curved surfaces where a single sucker might not be as good.

Dimensions: 80mm (h) x 60mm (dia) x 3

The excellent suction pod combined with an extra ball and socket head. This combination allows you to fine tune the angle you point the camcorder, making it even better for interior shots when mounted on windows.

This suction mount will allow you to mount a bullet cam or small camcorder in the inside of your windscreen and have the camera facing back out again.

Dimensions: 160mm x 95mm (dia)

This mount is our best seller. Not only suitable for bullet cameras but also good with small camcorders and digital stills cameras. It has three extra large suckers and fitted with a 3" extension bar so you can use this on the inside of your windscreen and face the camera back around on itself. You can re-configure this suction mount and turn it in to a Compact Alloy Triple Suction Mount pictured above. So you're getting three or four suction mounts in one!

This is one of our own unique camera mounts and one we use all the time ourselves. Built to high specification with alloy and CNC machined parts.

Dimensions: 310mm x 60mm (dia) x 3

This mount is very much like the mount pictured above but uses four high quality suckers instead of three. This gives a greater degree of stability and allows the mounting of a larger camcorder. Better stability will give a smoother, more professional looking video. Will support cameras up to 4kg in weight when used internally. This suction mount has enough adjustability to face bullet cameras and camcorders back out of a windscreen.

Dimensions: 320mm x 75mm (dia) x 4

This mount is best suited for digital stills cameras (DSC's). The excellent suction pod combined with a mini tripod. This combination is very versatile and can be used together or seperately. When used together you can screw the suction mount to the centre pole of the tripod, giving you a stable 4 points of contact. The centre section of the tripod is removable, giving you an extension arm and swivel head. The feet are rubber coated and so will not damage your paintwork.

Strong mount ideally suited to in car filming and for use with an SLR camera.
Combines a strong Manfrotto pump cup base and a Manfrotto 3D Junior tripod head, with a large rubber platform for attaching the camera.

Manfrotto pump cups provide the ultimate in suction and stability. These mounts use very high quality components indeed. These are widely used by professionals in the filming industry.

150mm vacuum pump cup, with swivel and double ball tilt top. A bit of a mouthful, but basically a very strong vacuum mount with multiple joints to allow easy camera positioning in almost any angle, inside and out. The mount is held in place on a smooth, clean angle (ideally flat or very shallow angle) by a vacuum. This is created by you pumping a button on the base quickly until you see the red line on the button disappear. At this point the cup is rated as supporting up to 2kg in weight. When the red line re-appears you need to start pumping again!

At last! A solution for trackdays, for those of you with cars that have race type seats and no roll cage.
Will fit most cars with rear windows i.e Impreza, Evo, Type R.
It mounts between both rear windows, using a total of 6 suckers, backed up by two safety tethers to attach to a fixed point behind the mount (rear seatbelt or similar) and a further strap that attaches to the hand strap of the camcorder.
This version has a ball and socket head, allowing the camcorder to sit on top of the mount.
Our testing has shown you get very stable results, better even than many other suction mounts. This is down to the two seperate mounting points, together with the rigidity of the box section profile of the bar.
Designed and tested by Fast Films, this mount came about after requests made at the various car shows we attend.

The three metal sections of the mount are telescopic, giving you a minimum width of 110cm (43 1/4") and a maximum width of 162cm (63 3/4"). This is enough to fit most of the usual cars with fixed back, racing type seats - (we have only tested some of these, but from dimensions and images seen this mount should fit fine)

This is the same excellent mount as described above, with the addition of a Manfrotto double ball tilt top head, allowing you more adjustment for angle. It means you can mount the camcorder underneath the bar, helping with stability and lowering the position of the camcorder in the car.
This could be important if you have high rear windows - you don't want to be viewing the roofline!

We are currently working on getting approval from all of the trackday companies. So far the response has been excellent.
When using this mount on track with a camcorder, do see the event organiser and marshall as you go out of the pits and explain and demonstrate that this is not a regular type of suction mount. Their fears are that in the event of an accident a camcorder can come loose and hit you. With our mount you can show that this is extremely unlikely to happen.

The three safety straps are to be used in the unlikely event of you having an accident on track, and can help you get approval from Marshalls to get on track.

An ideal mount for larger camcorders and digital SLRs (rated to 3kg), as used by BBC's Top Gear.
The mount includes two pump cup bases, a large camera plate, joints and an alloy arm.
Can be mounted horizontally or vertically, inside or outside the car. This suction mount is versatile and very professional. A high quality corked camera base is used to provide protection to your camera equipment.

Strong and stable.
Twin vacuum bases give security.
Well proven.
Easy to set up and attach.

We are regularly asked for a mount which can support the weight of an SLR and lens some distance from a car.
It's been surprisingly difficult to develop a kit which is easy to set, not too heavy, and stable when in use. We have had a whole selection of these parts in stock and had input from a number of pro photographers before this kit was produced.
This is the result! The pro mount is a superb mount for the money, ideally suited to SLRs and camcorders, holding upto 6kg in weight depending on configuration.

A flexible kit, with a number of accessories and extensions to give you the angle you require.

3 x vacuum bases with swivel.
2 x Swivel joints
2 x 100cm alloy extensions
2 x 50cm alloy extensions
2 x 12.5cm alloy extensions
1 x ball head
1 x collar to further extend
1 x large cork cushioned camera plate.

New: Click the images on the left to see shots taken using this camera mount.